Navcom LAND-PAK Quick Start Rev.B Manual do Utilizador descarregar pdf

LAND-PAK Quick-Start Guide

96-310039-3001, Rev. C 1 of 7

Follow this guide to set up the standard configuration for the

LAND-PAK base and rover, and the internal radio modem.

With minimal setup time, LAND-PAK™ can be configured and

operating to the point of collecting positions with

RTK/UltraRTK™.

By opening, assembling, and using this product, you

agree to the terms of the License Agreement contained

in the LAND-PAK Product User Guide.

Important: This device will not track satellites until after

the option file is loaded in the receiver. See instructions

contained in this guide.

Refer to the supplied LAND-PAK User Guide to check

inventory, charge batteries, and set up hardware.

Refer to these supplied guides for complete instructions for

optimum performance:

 NavCom LAND-PAK User Guide

 NavCom SF-3040 GNSS Receiver Product User Guide

 MicroSurvey Nautiz X7 User Guide

 MicroSurvey FieldGenius User Guide

 SATELLINE-3ASd Radio Modems User Guide

 StarPoint User Guide

 NavCom Customer Support:

Telephone: +1 (310) 381-2000

Web: http://www.navcomtech.com/Contact/ContactSupport.cfm

Install UHF Radio

Follow these steps to install the radio:

1. Turn the SF-3040 off.

2. Slide the release button downward on the radio bay.

3. Insert the multi-pin end of the radio in the bay with the

contact-side up, until a click is heard.

4. Carefully align the coaxial cable MCX connector center pin

with the radio module. Press the connector on straight

with significant pressure and without damaging the center

pin.

5. Route the cable to prevent pinching.

6. Close the door until it clicks shut.

7. Connect the radio antenna to the TNC connector.

Refer to the SF-3040 Product User Guide for additional

detail.

SF-3040 Battery Installation

Charge the batteries in accordance with the steps outlined in

the SF-3040 Product User Guide.

 New batteries must be charged for a minimum of

12 hours prior to use, regardless of the LED

indicator on the charger.

The battery chambers are located on the side of the

SF-3040 receiver. There are two locking clips on the outside

edge of each battery chamber to hold the battery packs in

place.

Follow these steps to install the battery packs:

8. Open the battery pack chamber (located on the left-

hand side of the SF-3040 as you hold the receiver with

the front facing toward you) by pressing downward on

the black button.

9. Align the battery pack with the chamber.

10. Holding the locking clip to the side, insert a battery pack

into each chamber, metal-contact end first.

11. Push the locking clips back into place.

Repeat steps 8 through 11 with the second battery pack.

 Refer to the supplied SF-3040 GNSS Receiver

Product User Guide for complete details on battery

charging, installation, use, safety, and disposal.

The SF-3040 GNSS receiver battery packs are keyed to

prevent improper installation. There are two locking clips on

either side of the battery bay.

 Ensure that both locking clips are locked in place.

If both locking clips are not locked in place, the

battery packs can disengage.

POWER

COM2

USB – COM1

MCX

Antenna

Cable

Interface Connectors

MCX

Antenna

Connector

SF-3040 Radio Bay

Release Button

Locking

Clip

Locking

Clip

Release

Button

1 2 3 4 5 6 7

Resumo do Conteúdo

Página 1 - LAND-PAK Quick-Start Guide

LAND-PAK Quick-Start Guide 96-310039-3001, Rev. C 1 of 7 Follow this guide to set up the standard configuration for the LAND-PAK base and rover, an

Página 2 - Establish Communications

2 of 7 LAND-PAK Quick-Start Guide, Rev. C Connect Equipment 12. Fully charge the battery packs in the supplied battery charger before operation.

Página 3

LAND-PAK Quick-Start Guide 96-310039-3001, Rev. C 3 of 7 Upload Software Options  Software Options must be uploaded before the StarFire License (i

Página 4 - Upload the StarFire License

4 of 7 LAND-PAK Quick-Start Guide, Rev. C Upload Firmware Upload a Unified Firmware File 39. Select Unified File Loader on the File Upload windo

Página 5

LAND-PAK Quick-Start Guide 96-310039-3001, Rev. C 5 of 7 Dual:GNSS, indicates that the receiver is navigating in the new StarFire format which supp

Página 6 - Bluetooth Interface

6 of 7 LAND-PAK Quick-Start Guide, Rev. C Figure 4: Pole Clamp and Cradle Refer to Figure 4 for the steps below: 62. Connect the rover pole cla

Página 7

LAND-PAK Quick-Start Guide 96-310039-3001, Rev. C 7 of 7 74. From the dropdown lists, select: a. Make: NavCom b. Model: SF-3040 c. Port: Blueto

Mais documentos para Equipamento Navcom LAND-PAK Quick Start Rev.B

Para ver o documento Navcom LAND-PAK Quick Start Rev.B Manual do Utilizador

Navcom LAND-PAK Quick Start Rev.B Manual do Utilizador (7 páginas)

Comentários a estes Manuais

Sem comentários

Navcom LAND-PAK Quick Start Rev.B Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Equipamento Navcom LAND-PAK Quick Start Rev.B. NavCom LAND-PAK Quick Start Rev.B User Manual Manual do Utilizador

Resumo do Conteúdo

Mais documentos para Equipamento Navcom LAND-PAK Quick Start Rev.B

Comentários a estes Manuais

Manuais e produtos relacionados com Equipamento Navcom LAND-PAK Quick Start Rev.B